OBD2 Code P0335 Nissan: Crankshaft Position Sensor A Circuit Malfunction

The OBD2 code P0335 in a Nissan vehicle indicates a problem with the Crankshaft Position Sensor A circuit. This sensor is critical for engine operation, and a malfunction can lead to various drivability issues. This article will provide a comprehensive guide to understanding, diagnosing, and resolving the P0335 code in Nissan vehicles.

Understanding the P0335 Code in Nissan Vehicles

The Crankshaft Position Sensor (CKP) is a vital component of your Nissan’s engine management system. It monitors the crankshaft’s position and rotational speed, relaying this information to the Engine Control Unit (ECU). The ECU uses this data to control ignition timing and fuel injection. When the CKP sensor or its circuit malfunctions, the ECU receives incorrect or no signal, triggering the P0335 code and potentially causing performance problems. This code specifically refers to the “A” circuit of the sensor, usually indicating a wiring or connection issue within that circuit.

Common Symptoms of a P0335 Code

A P0335 code can manifest in several ways, affecting your Nissan’s performance and drivability. These symptoms include:

Engine stalling: One of the most common symptoms is the engine stalling, especially at idle or low speeds.
Difficulty starting: The engine may crank but fail to start, or it might require extended cranking.
Rough idling: The engine may idle erratically or roughly.
Reduced engine power: You may experience a noticeable decrease in engine power and acceleration.
Check Engine Light illuminated: The check engine light is a universal indicator of a problem within the engine management system.

Diagnosing the P0335 Code

Diagnosing the P0335 code involves a systematic approach to pinpoint the root cause of the problem. Here’s a step-by-step guide:

Retrieve the code: Use an OBD2 scanner to confirm the P0335 code.
Visually inspect the CKP sensor and wiring: Look for any signs of damage, corrosion, or loose connections to the crankshaft position sensor. Pay close attention to the wiring harness and connector.
Check the sensor connector: Disconnect the CKP sensor connector and examine the terminals for any damage or corrosion.
Test the sensor circuit: Using a multimeter, test the voltage and resistance of the CKP sensor circuit. Compare the readings with the manufacturer’s specifications.
Test the CKP sensor: Test the sensor itself using a multimeter or an oscilloscope to ensure it is functioning correctly.

Common Causes of the P0335 Code in Nissan Vehicles

The P0335 code can be triggered by various factors, including:

Faulty Crankshaft Position Sensor: The sensor itself may be damaged or worn out, requiring replacement.
Damaged wiring: The wiring harness leading to the sensor can be damaged by heat, vibration, or rodents, leading to a short circuit or open circuit.
Loose or corroded connections: Corrosion or loose connections at the sensor connector can disrupt the signal transmission.
Damaged reluctor ring: The reluctor ring, a toothed wheel on the crankshaft, can be damaged, affecting the sensor’s ability to read the crankshaft’s position.
ECU malfunction: In rare cases, the ECU itself may be faulty, misinterpreting the signals from the sensor.

Fixing the P0335 Code

Once you’ve identified the cause of the P0335 code, you can take the appropriate steps to fix the problem. Common solutions include:

Replacing the Crankshaft Position Sensor: If the sensor is faulty, replacing it is usually the most effective solution.
Repairing the wiring: Repair or replace any damaged wiring in the sensor circuit.
Cleaning or replacing the connector: Clean the sensor connector terminals or replace the connector if it’s damaged.
Replacing the reluctor ring: If the reluctor ring is damaged, it needs to be replaced.
Reprogramming or replacing the ECU: In rare cases, the ECU may need to be reprogrammed or replaced.

“A faulty crankshaft position sensor can cause significant drivability problems. Accurate diagnosis is crucial to avoid unnecessary repairs.” – John Smith, Automotive Diagnostic Specialist

Conclusion

The OBD2 code P0335 in your Nissan indicates a problem with the crankshaft position sensor circuit. Addressing this issue promptly is essential to restore your vehicle’s performance and prevent further damage. By understanding the symptoms, causes, and diagnostic procedures, you can effectively troubleshoot the P0335 code and ensure your Nissan runs smoothly. codigo obd2 p0335 nissan

Nissan Engine Bay After P0335 Code Repair

FAQ

What is the OBD2 code P0335? The P0335 code refers to a malfunction in the Crankshaft Position Sensor “A” circuit.
Can I drive my Nissan with a P0335 code? While you might be able to drive for a short distance, it’s not recommended. The problem can worsen and lead to more severe issues.
How much does it cost to fix a P0335 code? The cost can vary depending on the specific cause and the required repairs, but typically ranges from $100 to $400.
What tools do I need to diagnose a P0335 code? You’ll need an OBD2 scanner and a multimeter, at minimum.
Is the P0335 code specific to Nissan? No, the P0335 code is a generic OBD2 code that applies to various vehicle makes and models.
Can a bad battery cause a P0335 code? While unlikely, a severely discharged or faulty battery can sometimes cause sensor-related issues.
How can I prevent a P0335 code in the future? Regular maintenance and inspections can help prevent issues with the crankshaft position sensor and its circuit.

For further assistance, contact us via WhatsApp: +1(641)206-8880, Email: [email protected] or visit us at 789 Elm Street, San Francisco, CA 94102, USA. Our customer service team is available 24/7.