4 System Diagnostics + 8 Reset Functions + 10 Obdii Modes + Health Report Print + Battery Voltage Graph + Auto VIN + Feedback + 4 in 1 Data Graph

What makes more than 100,000 technicians choose Launch CRP129E?More convenient, more professional, more commonly used reset function ?

EPB Service

• 1、When the brakes are used to a certain thickness, the brake sensor line will be worn flat. At this time, the brake pad sensing line will send a signal to the car computer, prompting to replace the brake pads. After replacing the brake pads, you need to reset the brakes, otherwise the car will alarm. When do I need to use EPB reset? a) After replacing the brake pads and the brake pad wear sensor wire; b) After the brake pad indicator light comes on; c) After the brake pad sensor circuit short circuit is repaired; d) After replacing the servo motor.

SAS Reset

• 1. Steering angle reset is to find the relative zero position where the car keeps driving straight. With this position as a reference, the ECU can calculate the exact angle when turning left and right. 2. After replacing the steering angle position sensor, replacing the mechanical parts of the steering system (such as: steering gear, steering column, tie rod ball head, horn), after completing the four-wheel alignment, body repair, etc., this function is usually needed.

TPMS Services

• 1. When the tire pressure fault light is on, after maintenance, you can reset the tire pressure through the tire pressure reset function and turn off the tire pressure fault light. 2. If the tire pressure is too low or leaks, replace or install tire pressure monitoring equipment, replace tires, if the tire pressure sensor is damaged, and the tires with tire pressure monitoring function are rotated, etc., use TPMS after the repair is completed. Let the car work normally after the reset function.

Oil(Lamp) Reset

• 1.The car oil light is on, indicating the vehicle to the maintenance period. After maintenance is completed, the mileage or driving time should be zeroed out so that the maintenance light goes off and the system starts a new maintenance cycle. 2.After changing the oil or replacing the electrical accessories that monitor the oil life, you need to use the maintenance light reset function.

Throttle Adaptation(Idle learning)

• 1 .Throttle matching is to use the car decoder to initialize the throttle actuator of the car, so that the learning value of the ECU returns to the initial state, thus adjusting the action of the throttle (or idle motor) can be more precisely controlled to regulate the intake air speed. Air volume. 2. You will use this function in the following 5 cases: a) When replacing the ECU, the new ECU does not store the characteristics related to throttle operation. b) After ECU power failure, the memory in ECU memory is lost. c) After replacing the electronic throttle. d) After replacing or removing the air inlet, it affects the control of idle speed by the ECU working in coordination with the throttle body. e) After cleaning the throttle, although the characteristics of the idle throttle potentiometer are not changed, the air intake volume is changed and the idle speed control characteristics are changed with the same throttle opening.

New features added for the 30th anniversary of the LAUNCH brand (available with software upgrade).

Injector Coding:1) Write the actual code of the injector nozzle or rewrite the code stored in the ECU to correspond to the code of each cylinder nozzle, so as to more accurately control or correct the amount of fuel injected into each cylinder. (2) Usually, after replacing the ECU and injector nozzles, it is necessary to confirm or recode the code for each cylinder nozzle. So that the cylinder can better identify each cylinder nozzle and accurately control the oil injection.

BAT battery service(BMS)BMS Reset:Evaluate the battery charge state, monitor the closed-circuit current, register the battery replacement, etc.;

Diesel Particulate Filter (D.PF) Regeneration:You will use this function when you encounter these situations, a) Exhaust back pressure sensor replacement; b) Particle trap removal or replacement; c) Fuel additive nozzle removal or replacement; d) Catalytic oxidizer removal or replacement; e) D.PF regeneration fault light illuminated after repair and matching; f) D.PF regeneration control module repair and replacement, etc.It can periodically use combustion oxidation (e.g. high temperature heating combustion, fuel additives or catalysts to reduce the combustion of particulate matter ignition point) to remove the trap performance is always optimal and stable.

LAUNCH 4 SYSTEM CODE READER AND SCAN TOOL

LAUNCH CRP129E supports precise troubleshooting of the 4 major electronic control systems on the vehicle, intuitive data flow monitoring, clearing faults and obtaining health diagnostic reports, etc.

Transmission Control System (TCM System): Keep your car’s transmission running smoothly with our diagnostic tool. The Launch CRP129E allows you to read and clear codes, view live data, and retrieve error information from your Automatic Transmission (AT). This type of transmission changes gear ratios automatically, so you don’t have to worry about shifting gears manually.

Anti-Lock Braking System (ABS System): Your diagnostic tool can help you keep your Anti-Lock Braking System in top condition. You can read and clear DTCs data flow and perform various tests to check the operating conditions of your ABS system. Plus, you can turn off the warning light to ensure your safety on the road.

Supplemental Restraint System (SRS System): Safety is a top priority when it comes to driving. The scan tool can detect every electronic parameter of your SRS (Airbag) system to check its health status. You can read and clear fault codes and turn off the warning light of your airbag to make sure your engine is working properly and safely.

Engine System(ECM System): LAUNCH crp129e diagnostic tool can help you enhance your vehicle performance, save energy, and reduce exhaust emission. You can detect the engine ignition, fuel injection, air and fuel ratio, and exhaust emission conditions in Engine system with ease. Keep your car running smoothly and efficiently with our diagnostic tool.

How do I use it?

• After connecting the 16PIN port of CRP129E to the vehicle, start the CRP129E and turn on the ignition key, the system enters auto-detection mode and once the system successfully obtains the VIN (Vehicle Identification Number) information of the currently identified vehicle, it will detect the vehicle. If the tool cannot get the VIN information, you can also perform the vehicle diagnosis manually.

Supports Full OBDII Protocol(When your car flashes “Check Engine” or “Service Engine Soon,” it means you gotta utilize this feature.)

• LAUNCH CRP129E OBD2 Car Scanner – the ultimate tool for all your car diagnostic needs! Unlike many other OBD readers on the market, our scanner supports ALL OBD2 protocols. We understand that many OBD2 scanners claim to work with all protocols, but struggle with the J1850 protocol used in many Ford and General Motors vehicles. The ISO9141 protocol also poses problems for many other OBD readers, and is commonly found in Chrysler, Honda, and Toyota cars. But fear not – our OBD reader actually works with these protocols, earning us a reputation for reliability and accuracy.
• The OBDII function is made to keep an eye on the vehicle emission control system and important engine parts, testing specific parts and vehicle conditions on a regular or ongoing basis. It has its own menu, with features like EVAP testing, O2 sensor testing, freeze frame, I/M readiness, MIL status, check VIN information, and onboard monitoring,etc.

Don’t settle for anything less than the best – choose the LAUNCH CRP129E OBD2 Car Scanner for all your car diagnostic needs!

LAUNCH CRP129E OBD2 SCANNER TECHNICAL SPECIFICATIONS

1. • Screen: 5” color touch screen.
2. • RAM: 2GB • ROM: 16GB
3. • OBD II input voltage range: 9~18V
4. • Charging via: DC 5V charging cable or diagnostic cable through connection to vehicle’s DLC
5. • Dimension: 8.97inch x 4.92inch x1.36inch
6. • Working temperature: -10 to 50°C (14 to 122 F°)
7. • Storage temperature: -20 to 70°C (-4 to 158 F°)

Support 57 Makers and Over 100,000+ Car Model : for Chevrolet, for Jeep, for JAGUAR, for Vauxhall, for Infiniti, for USAFORD, for HYUNDAI, for TOYOTA, for HONDA, for Tlisuzu, for Gmsa, for SUZUKI, for GM, for FIAT, for SPRINTER, for Euroford, for SMART, for EOBD2, for SKODA, for Dodge, for SEAT, for DEMO, for SAMSUNG, for DAEWOO, for SAAB, for DACIA, for RENAULT, for CITROEN, for PORSCHE, for PEUGEOT, for OPEL, for Cadillac, for for Nissan, for Buick, for BUGATTI, for MITSUBISHI, for BMW, for Mini, for BENZ, for MAZDA, for AUTOSEARCH, for Lincoln, for AUSTFORD, for Lexus, for LANDROVER, for Alfa Romeo, for Lancia, for ACURA, for KIA, for Abarth, for JPISUZU, for etc.

WHAT YOU WILL GET IN THE PAKEAGE?

• 1.LAUNCH Creader Professional CRP129E OBD2 Scanner handset.
• 2. OBD2 diagnostic cable
• 3. DC 5V charging cable
• 4. User manual
• 5. Carrying bag